#
Skip to main content

Teltonika RUT956*2 industrial cellular Router

Product information "Teltonika RUT956*2 industrial cellular Router"

 
 
RUT956 is an industrial router that combines cellular, Wi-Fi, and wired connectivity options with automatic WAN failover and GNSS capabilities.
Serial communication interfaces enable integrating more varied devices into the solution ecosystem,
while I/O and advanced RutOS software facilitate equipment control, automation, and event notifications.
 
 
MOBILE
 
 
Mobile module4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps
SIM switch2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection
StatusIMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC
SMS

 
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
USSDSupports sending and reading Unstructured Supplementary Service Data messages
Black/White listOperator black/white list (by country or separate operators)
Multiple PDNPossibility to use different PDNs for multiple network access and services
Band managementBand lock, Used band status display
APNAuto APN
BridgeDirect connection (bridge) between mobile ISP and device on LAN
Passthrough

 
Router assigns its mobile WAN IP address to another device on LAN
 
NETWORK 
HotspotCaptive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes and option to upload and download customised hotspot themes
RoutingStatic routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing
Network protocolsTCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)
VoIP passthrough supportH.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Connection monitoringPing Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
FirewallPort forward, traffic rules, custom rules
DHCPStatic and dynamic IP allocation, DHCP Relay
QoS / Smart Queue Management (SQM)Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
DDNSSupported >25 service providers, others can be configured manually
Network backupWi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover
Load balancingBalance Internet traffic over multiple WAN connections
SSHFSPossibility to mount remote file system via SSH protocol
 
WIRELESS
 
 
Wireless modeIEEE 802.11b/g/n, Access Point (AP), Station (STA)
WiFi securityWPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation
SSID/ESSIDSSID stealth mode and access control based on MAC address
Wi-Fi usersUp to 100 simultaneous connections
Wireless Connectivity FeaturesFast roaming (802.11r), Relayd, BSS transition management (802.11v), radio resource measurement (802.11k)
Wireless MAC filterWhitelist, blacklist
 
ETHERNET
 
 
WAN1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX
LAN
 
3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
 
MODBUS
 
 
Supported modesServer, Client
Supported connection typesRTU (RS232, RS485), TCP, USB
Custom registers

 
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality
Supported data formats8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
 
MQTT GATEWAY
 
 
MQTT Gateway

 
Allows sending commands and receiving data from MODBUS Server through MQTT broker
DNP3
 
 
Supported modes
 
TCP Master, DNP3 Outstation, RTU Master
SYSTEM CHARACTERISTICS
 
CPUMediatek, 580 MHz, MIPS 24KEc
RAM128 MB, DDR2
FLASH storage
 
16 MB, SPI Flash
INPUT / OUTPUT
 
 
Input1 x digital dry input (0 - 3 V), 1 x digital galvanically isolated input (0 - 30 V), 1 x analog input (0 - 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 - 5 V detected as logic low, 8 - 30 V detected as logic high)
Output1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector)
EventsEmail, RMS, SMS
I/O juggler
 
Allows to set certain I/O conditions to initiate event
 
POWER
 
 
Connector4-pin industrial DC power socket
Input voltage range9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max
PoE (passive)Passive PoE over spare pairs. Possibility to power up through LAN1 port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, 9 - 30 VDC
Power consumption
 
< 2 W idle, < 7 W Max
PHYSICAL INTERFACES (PORTS, LEDS, BUTTONS; SIM)
 
Ethernet4 x RJ45 ports, 10/100 Mbps
I/O’s2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connector (available from HW revision 1600)
Status LEDs1 x Bi-color connection status, 5 x Mobile connection strength, 4 x ETH status, 1 x Power
SIM2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional)
Power1 x 4-pin power connector
Input/output1 x 10-pin industrial socket for inputs/outputs
Antennas2 x SMA for LTE, 2 x RP-SMA for Wi-Fi, 1 x SMA for GNSS
USB1 x USB A port for external devices
RS2321 x DB9 socket
RS4851 x 6-pin industrial socket
Reset
 
Reboot/User default reset/Factory reset button
PHYSICAL SPECIFICATION
 
Casing materialAluminium housing, plastic panels
Dimensions (W x H x D)110 x 50 x 100 mm
Weight287 g
Mounting options
 
DIN rail (can be mounted on two sides), flat surface placement
PACKAGE CONTAINS
 
 
  • RUT956 router
  • 9 W EU PSU PR3PUEU3
  • 2x Mobile antennas (magnetic mount, SMA male, 3 m cable)
  • 2x Wi-Fi antennas (magnetic mount, RP-SMA male, 1.5 m cable)
  • GNSS antenna (adhesive , SMA male, 3 m cable)
  • RS485 connector block
  • I/O connector block
  • Ethernet cable (1.5 m)
  • SIM Adapter kit
  • QSG (Quick Start Guide)
  • Packaging box
Ethernet Ports: 1, 2
Mobilfunkstandards: 2G, 3G, 4G
Wifi Standards: Dual-Band 802.11 b/g/n/ac, 2.4 GHz 802.11 b/g/n

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.